SDI Technologies MP3 Docking Station IP42 User Guide

Model iP42  
The Home System  
For Your iPhone® or iPod®  
 
Table of Contents  
Quick Start .........................................................................................................................................................................1  
Controls and Indicators ....................................................................................................................................................2  
iP42 Display.......................................................................................................................................................................2  
Installing/Replacing iP42 Backup Batteries / Battery Warning ..........................................................................................3  
Setting Up the iP42 ............................................................................................................................................................4  
Using the iP42 Alarms.............................................................................................................................................. 5-6  
Listening to iPhone/iPod, Radio or Aux devices........................................................................................................ 6-7  
Sleep mode, Dimmer and more......................................................................................................................................7  
A Consumer Guide to Product Safety...............................................................................................................................8  
Troubleshooting ........................................................................................................................................................... 9-10  
Warranty Information .......................................................................................................................................................11  
A Consumer Guide to Product Safety  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may  
not cause harmful interference, and (2) this device must accept any interference received, including interference that may  
cause undesired operation.  
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits provide reasonable  
protection against radio and TV interference in a residential area.  
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference you can  
try one or more of the following corrective measures:  
Reorient or relocate the receiving antenna.  
Increase the distance between the equipment and the radio or TV.  
Use outlets on different electrical circuits for the equipment and the radio or TV.  
Consult your dealer or an experienced radio/television technician if the problem still exists.  
Modifying or tampering with your system’s internal components can cause a malfunction and might invalidate the system’s warranty  
and void your FCC authorization to operate it.  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
Maintenance  
Place the unit on a level surface away from sources of direct sunlight or excessive heat.  
Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material should  
be placed between it and the furniture.  
Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzene, thinner  
or similar materials can damage the surface of the unit.  
 
Controls and Indicators  
Top Panel  
Dock  
EQ Button  
Preset Buttons 1-6  
Volume Wheel  
Set Wheel  
Alarm Reset / Power Button  
Play/Pause Button  
Radio/aux Button  
Alarm 2 Button  
Alarm 1 Button  
Sleep Button  
Snooze/Dimmer Button  
Time Set/ Sync Button  
Rear Panel  
DST switch  
Time Zone Button  
time set/ sync  
line-in  
time zone  
DC 7.5V 2A  
DST  
AC Adaptor Jack  
aux line-in Jack  
-1  
+1  
FM antenna  
iP42 Display  
NOTE: AM/PM indicators will not appear  
when clock is set to 24 hour display mode  
Time Display  
PM Indicator  
AM Indicator  
Battery Low Indicator  
wake to  
Wake to Icon  
Sleep Mode Icon  
Alarm Indicators  
FM Radio Indicator  
Alarm Time Display  
2
 
Installing/Replacing the iP42 Backup Batteries  
The iP42 uses “AA” LR06 batteries (pre-installed) for backup battery system to provide  
continuous alarm operation and clock settings in the event of a power failure. If the Battery  
Low Icon located on the right of the display is flashing, it is time to replace the backup  
batteries. Please make sure the AC adaptor is connected, otherwise all settings may be lost  
during battery replacement.  
1. Open the battery compartment cover located on the bottom of the unit  
2. Insert 2 “AA” (LR06) batteries as indicated, making sure that the + and – polarities match  
the diagram inside.  
3. Replace battery compartment cover.  
We recommend alkaline batteries for longer battery life.  
Battery Warning  
For models that require more than one battery  
• Do not mix with used or other battery types/brands  
• Replace all batteries at the same time  
• Do not open batteries  
• Do not dispose of in fire  
• Do not heat above 75ºC (167ºF)  
• Do not expose contents to water  
• Do not charge or recharge  
• Do not install backwards  
 
3
Setting Up the iP42  
Connect iP42 to Power Source  
Plug the AC adaptor cable into the AC Adaptor Jack and the other end into a standard 120V AC wall socket. Adaptor must  
be plugged in to operate unit. The iP42 does not operate on batteries (a battery back up system maintains clock settings  
during power failures).  
This unit is a preset clock: the clock is preset at the factory. Its simple to match the Time Zone setting to your location (US  
only).  
1. Depending on your location and whether or not Daylight Saving Time (DST) is in effect, manually set the DST Switch located  
at the back of the unit to +1 to add an hour or to -1 to subtract an hour. A DST adjust screen appears briefly.  
2. Press and hold the Time Zone Button located on the back of the unit until the Time Zone flashes on the lower part of the  
display. Turn the Set Wheel to select your time zone. Note: Time Zone is disabled when clock display is set to 24 hours  
(see step 5 under Setting Time).  
3. Press the Time Zone Button again (or no button within 10 seconds) to exit the time zone setting mode.  
4. If the displayed time is not correct, please see “Setting Time and Calendar manually” section below.  
Sync Time to iPhone/iPod  
The iP42 Time Sync feature allows you to sync the time setting on the iP42 to the time from your iPhone or recent model iPod  
Touch, iPod Nano and iPod Classic (older iPod models such as iPod mini do not support this feature).  
1. Dock your iPhone or iPod  
2. Press the Time Sync Button located at the back of the unit.  
3. The iP42 will sync to the time on your iPhone/iPod. Once sync is completed,“SYNC OK” will appear on the display.  
4. If sync was not successful, “Failed” will appear on the display. If this happens, please try again, with a different iPhone/iPod  
if needed. If time sync still fails, please set time manually (see below).  
NOTE: The iPhone is constantly updated to current time via cell phone towers. The time on your iPod is only accurate to the  
last time it was synced to a computer. Its possible to have up to 59 seconds difference between the iP42 and synced  
iPhone/iPod.  
Setting Time and Calendar manually  
1. Press and hold the Time set/sync Button located at the back of the unit until the time flashes on the display.  
2. Turn the Set Wheel to the correct time. Remember to set the correct AM or PM time. The AM/PM Indicators appear to  
the left of the time display (except when clock display is set to 24 hour mode-- see step 5).  
3. Press the Time set/sync button again. The year will flash. Turn the Set Wheel until the current year is displayed.  
4. Press the Time set/sync button again. The month and date will flash. Turn the Set Wheel until the current month/date  
is displayed.  
5. During Time set, press either the  
or  
button to toggle the clock display format to 12 hours or 24 hours.  
6. Press the Time set/sync button again (or no button within 10 seconds) to exit the time/calendar setting mode.  
 
4
Using the iP42 Alarms  
Using the Alarms  
iP42 has a dual alarm system so you can set two separate alarms to different alarm times, wake-to sources and frequencies  
(daily, weekdays or weekend).  
Setting the Alarms  
1. Press and hold the  
or  
Button until the alarm time flashes on the lower part of the display. Turn the Set Wheel to  
set the alarm time. Remember to set the correct AM or PM time.  
2. Press the Alarm Button again to confirm the desired alarm time and then turn the Set Wheel to set the alarm frequency  
(7 = the whole week, 5 = weekdays, 2 = weekends only).  
3. Press the Alarm Button again to confirm alarm frequency then turn the Set Wheel to select an alarm source to wake to:  
Buzzer, Playlist (user created), iPhone/iPod or Radio.  
NOTE: to wake to playlist, you must first create a playlist named “iHome”. The iP42 will play music randomly from within  
the “iHome” playlist.  
If the selected alarm source is iPhone/iPod and no iPhone/iPod is docked/detected, the iP42 will default to a buzzer alarm.  
4. For wake to radio, after selecting Radio as wake to source, press the Alarm Button again and turn the Set Wheel to  
select a different radio station or press one of the preset buttons to wake to a preset radio station (see Using Radio on page  
6 for details on setting radio stations and presets).  
5. Press the Alarm button again (or no button within 10 seconds) to exit the alarm setting mode. The alarm will be armed  
once set and the corresponding alarm icon will light up. The lower part of the display will show the earliest set alarm time.  
Reviewing, Arming and Disarming Alarm (Turn Alarm Function On and Off)  
1. Once an alarm is armed, the lower part of the display will show the alarm time and the alarm icon. If more then one alarm  
is armed, the earliest alarm time will show along with both icons.  
2. To review the alarm time, press an alarm button once. The related alarm time will show on the lower part of the display.  
3. During alarm review, press the alarm button once to toggle it on or off. If the alarm is armed, the related alarm icon will light  
up.  
Resetting the Alarm to Come on the Next Day  
When an alarm is sounding, press the  
Button to stop the alarm and reset it to come on the next set day. For example, if  
an alarm is set for 5 days and you press the alarm reset on Friday, the alarm will come on again on Monday, not Saturday.  
Snooze Operation  
1. Press and hold the Snooze/Dimmer Button for a few seconds until the snooze time flashes. Turn the Set Wheel to set  
the snooze timer from 1 to 29 minutes.  
2. Press the Snooze/Dimmer Button after an alarm sounds. The alarm will be silenced for the set snooze duration time then  
sound again. Snooze can be pressed several times during the 1 hour alarm cycle.  
 
5
Using the iP42 Alarms  
Sure Alarm  
The iP42 has a sure alarm feature. If backup batteries are installed, the buzzer alarm will still sound in the event of a power  
failure.  
Listening to iPhone/iPod, Radio  
Charging your iPhone/Pod  
Note: Please make sure you are using the correct insert for your iPhone/iPod and that it is properly docked into the iP42.  
Failure to do so may damage your iPhone/iPod.  
While an iPhone/iPod is docked in the unit and the unit is connected to AC power, it recharges until fully charged.  
Listening to iPhone/iPod  
1. Dock an already-playing iPhone/iPod in the dock. The iP42 will automatically turn on and you will hear the audio playing  
from your iPhone/iPod.  
Note: If the playing song/music loudness is too low on the iPod itself, the iP42 may not detect iPod is in play mode. Press  
the  
Button to play it.  
2. When an iPhone/iPod is docked and in standby mode, press the  
Button to play it. “iPod” will appear briefly in the lower  
part of the display to show iPod is currently in play mode.  
3. Press the  
4. Turn the Volume Wheel to adjust the system volume.  
5. Press the EQ Button to select and turn the Set Wheel to adjust Treble, Bass, and Left/Right Balance.  
Button again to pause play; press again to resume it.  
6. To turn off the unit, press the  
Button. An iPhone/iPod will continue charging while docked.  
Listening to Radio  
Setting up Antenna  
Extend FM wire antenna fully for best reception. Do not strip, alter or attach to other antennas.  
Tuning and Playing the Radio  
1. Press the Radio Button as needed to turn on iP42 and choose between FM radio and aux line-in modes.  
2. When FM radio mode is selected, turn the Set Wheel to tune the radio to a desired station. The current radio frequency  
appears in the lower right of the display.  
3. To memorize a station as a preset, use the Set Wheel to select your station. Press and hold the desired Preset  
Button until odd number preset (P1, etc) flashes on display; press again for even number presets and allow to time-out.  
You will hear 2 beeps confirming the preset has been assigned.  
4. To access a preset station, press the desired Preset Button once (for odd number presets) or twice (for even number  
presets).  
5. Turn the Volume Wheel to adjust the system volume.  
6. Press the EQ Button to select and turn the Set Wheel to adjust Treble, Bass, and Left/Right Balance.  
7. To turn off the unit, press the  
Button. An iPhone/iPod will continue charging while docked.  
 
6
Listening to Aux device  
Using the aux line-in Jack  
You can play any iPod or other MP3 player or portable audio device through the iP42 via the aux line-in Jack.  
1. Plug one end of a standard stereo audio patch cord (not included) into the headphone or line-out jack on your device and  
the other end of the patch cord into the iP42 aux line-in Jack located on the back of the unit.  
2. Press the Radio Button until “aux” appears in the lower part of the display.  
3. Turn on and play your device.  
4. Turn the Volume Wheel to adjust the iP42 volume. You may need to adjust volume on your audio device, too.  
5. Press the EQ Button to select and turn the Set Wheel to set Treble, Bass, and Left/Right Balance.  
6. To turn off the unit, press the  
Button. Please remember to turn off your device, too.  
Sleep mode, Dimmer and more  
Sleep Operation  
Sleep mode lets you sleep to your iPhone/Pod or radio, gradually lowering the volume until the unit shuts off at the selected  
time.  
1. Press the Sleep Button to enter sleep mode. The sleep time will show in the lower display.  
2. Press the Sleep Button again as needed to adjust the sleep timer from 120, 90, 60, 30 or 15 minutes.  
3. When the display changes back to show the real time, press the Sleep Button once to show the sleep time remaining.  
Pressing it again will change sleep time to next lowest increment.  
4. iP42 has independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the normal  
volume. The sleep volume will remain at that level the next time you enter sleep mode until controls are changed.  
5. To stop listening at any time, press the  
Button to turn unit off.  
Dimmer Operation  
During normal operation, press the Snooze/Dimmer Button to control the brightness of the LCD display.  
Using the iP42 in Other Countries  
Different regions of the world use different FM radio frequency steps and ranges. You will need to select the one that matches  
the standards in your region (USA, EUROPE, JAPAN, AUSTRALIA,or CHINA). The default setting is USA; if you live in the US,  
you may skip this section.  
1. Make sure the iP42 is OFF (not playing in any mode). Press and hold the Radio Button for about 5 seconds until “USA”  
appears in the lower part of display. Tune the Set Wheel to adjust country frequency to your region.  
2. Press the Radio Button again (or no button within 5 seconds) to exit the radio frequency setting mode.  
 
7
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,  
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully  
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in  
these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For  
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it  
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through  
the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions  
or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched  
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where  
it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning  
instructions.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings  
or vents located on the product.  
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable  
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage  
to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in  
a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A.  
the power supply cable or plug has been damaged.  
B. objects have fallen into or liquid has been spilled into the enclosure.  
C. the unit has been exposed to rain.  
D. the unit has been dropped or the enclosure damaged.  
E.  
the unit exhibits a marked change in performance or does not operate normally.  
12. Antenna – Do not connect an external antenna to the unit (other than that provided).  
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power  
cable should be unplugged from the unit to prevent damage or corrosion.  
14. Servicing – The user should not attempt to service the unit beyond those methods described in the users operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.  
Download from Www.Somanuals.com8. All Manuals Search And Download.  
Troubleshooting  
Possible Problem  
Solution  
Symptom  
iP42 does not turn on AC adaptor isn't plugged into a working wall Plug the AC adaptor into a working wall socket and plug the  
socket or not plugged into the power supply  
jack on back of the unit  
connector into the supply jack on the unit  
If unit is plugged in and doesn't respond, try resetting the unit by  
following these steps:  
iP42 doesn’t respond  
iP42 requires a reset  
a) remove iPhone/iPod from dock  
b) unplug unit from power source  
c) remove back up batteries  
d) wait a few minutes, then resume use  
Remove your iPhone/iPod from the dock and check for  
obstruction on the connectors in the dock and on your  
iPhone/iPod. Then reseat it in the dock.  
iPhone/iPod is not docked properly  
Battery Low icon  
always flashing  
Batteries are weak  
Replace with new batteries  
Batteries were not installed properly  
Check to make sure the polarity ( + and – ends) matches the  
diagram in the battery compartment  
iPhone/iPod does  
not respond to the  
unit/iPod is playing  
but no sound comes  
out  
iPhone/iPod is not docked properly  
Your iPhone/iPod software is too old  
Remove your iPhone/iPod from the dock and check for  
obstruction on the connectors in the dock and on your  
iPhone/iPod. Then reseat it in the dock.  
Upgrade software on your iPhone/iPod via iTunes on your  
computer  
iPhone/iPod is locked up/plays but no  
sound comes out  
Check the volume setting. Make sure your iPhone/iPod is working  
properly before docking into the unit. Please refer to your iPhone/iPod  
manual for details. See above for software upgrade information.  
You may need to reset your iPhone/iPod. Refer to your iPhone or  
iPod user guide for details on how to perform a reset.  
Using 1st or 2nd generation iPod, iPod  
Shuffle or other devices.  
iP42 cannot control those iPod models or other devices.  
iP42/iPhone/iPod  
performance is erratic  
The iP42 is reacting to external interference  
Move unit away from potential sources of external interference such  
as computers, modems, wireless devices (routers) or fluorescent  
light.  
Volume is set too low on iP42  
Make sure volume is turned up  
No sound from iP42  
iPhone/iPod  
didn’t  
charge up  
iPhone/iPod is not installed properly  
Remove your iPhone/iPod from the dock and check for  
obstruction on the connectors in the dock and on your  
iPhone/iPod. Then reseat it in the dock.  
Please make sure your iPhone/iPod is working properly before  
docking into the unit. Please refer to your iPhone/iPod manual for  
details.  
iPhone/iPod is locked up/ frozen  
iPhone/iPod battery has problem  
 
9
Troubleshooting  
Possible Problem  
Solution  
Symptom  
Sound is distorted  
Volume level is set too high  
Decrease the volume  
If the iPhone/iPod original sound source (MP3) is old or of poor quality,  
distortion and noise are easily noticed with high-power speakers. Try  
a different audio source such as a music CD through the line-in jack.  
Sound source is distorted  
If you are using an external sound source like older generation of  
iPod or iPod Shuffle, try reducing the output volume on the device  
itself. Also try turning bass boost OFF.  
EQ settings are too high.  
This is normal  
Lower EQ  
settings.  
Unit/adaptor gets  
warm after extended  
play at high volume  
Turn unit off for a while or lower volume  
Snooze time  
Custom snooze time not set  
Press and hold Snooze button then turn Set Wheel to adjust  
When setting clock or alarm time, take note of the AM/PM indicators  
is too long/short  
Alarm not working  
AM/PM time/alarm time not set correctly  
Alarm time or source selected for alarm 2  
or alarm 3, not alarm 1, etc.  
Make sure to set the alarm time and source for the alarm icon 1,  
2 or 3 that is shown on the clock display  
7-5-2 days setting is not correct  
7 days is every day alarm, 5 days is Mon-Fri, and 2 days is Sat-Sun.  
See page 5 for setting alarms.  
Calendar is not set correctly, which can  
affect 7/5/2 day alarm operation  
See page 4 for Time/Calendar setting section.  
Make sure you are using an iPhone or newer iPod such as touch, nano  
or classic. If not available, set time manually (see page 4).  
Time sync didn’t work  
Older iPod models such as iPod mini do not  
support time sync function  
10  
 
Limited 1 Year Warranty Information  
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from  
defects in workmanship and materials, under normal use and conditions, for a period of 1 Year from the date of original purchase.  
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased.  
Should this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period,  
SDI Technologies will repair or, at its discretion, replace this product without charge (except for a $15.00 charge for handling, packing,  
return UPS/postage, and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product  
to the Factory Service Center listed below. The product must include proof of purchase, including date of purchase. The fee for service  
without proof of purchase is $30.00.  
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective  
batteries are the most common cause of problems encountered.  
If service is still required:  
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.  
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty  
period.  
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $15.00 ($30.00 without proof of purchase).  
4. Send the unit prepaid and insured, to the Factory Service Center listed below.  
Consumer Repair Department  
SDI Technologies Inc.  
1330 Goodyear Dr.  
El Paso, TX 79936-6420  
Disclaimer of Warranty  
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which  
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized  
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes  
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.  
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original  
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members  
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive  
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions  
may not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Your acknowledgment and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually  
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies  
product.  
Toll Free Customer Service: 1-800-288-2792  
 
iP42-030510-A(Ris)  
©SDI Technologies 2010 All rights Reserved  
Printed in China  

Quadra Fire Indoor Fireplace CB1200I User Guide
Radica Games Card Game 71054 User Guide
Radio Shack Scanner PRO 528 User Guide
RCA TV DVD Combo 15L500TD User Guide
Regency Indoor Fireplace L676E LP User Guide
RocketFish Switch RF NBSKHBP User Guide
Russound Speaker R12DT User Guide
Ryobi Battery Charger 130155001 User Guide
Samsung MP3 Player AH68 01669B User Guide
Schumacher Calculator PI 140 User Guide